Calibration tests are standard procedures applied to sensors not eliminated by screening tests . 校準試驗是對篩選試驗中未被淘汰的傳感器進行試驗的標準測試程序。
During calibration test weights are compared with appropriate standards 校正過程中,測試砝碼將與適當?shù)臉?biāo)準進行比較。
Calibration test equipment 校準檢驗置
Inquiring into calibration test of standard steel bottle and calculation of total deformation value 標準鋼瓶標定試驗及全變形值計算探討
Specification for radio disturbance and immunity measuring apparatus and methods - radio disturbance and immunity measuring apparatus - antenna calibration test sites for 30 mhz to 1 000 mhz 無線電干擾和抗擾測量?jī)x器和方法規范.無線電干擾和抗擾測量?jī)x器. 30mhz至1000mhz的天線校準試驗裝置
Specification for radio disturbance and immunity measuring apparatus and methods - part 1 - 5 : radio disturbance and immunity measuring apparatus - antenna calibration test sites for 30 mhz to 1 000 mhz 無線電干擾和抗擾的測量設備和方法的規范.第1 - 5部分:無線電干擾和抗擾的測量設備. 30 mhz至1 000 mhz的天線校正試驗裝置
5 . the methods of temperature - correcting on copper cylinders and copper spheres are discussed . the method of unitive temperature - correcting on plastic pressue - measuring elements is put forward for the first time . large quantities of quasi - dynamic calibration tests in different temperatures are carried out on the dropper - hammer hydraulic dynamic pressure calibration device and the unitive temperature - correcting formula which accords with the traditional correcting method is got 在落錘液壓動標裝置上組織了多批次的銅柱、銅球高低溫準動態校準試驗,探討了建立溫度誤差統一修正公式的可行性,建立了測壓銅球,測壓銅柱符合我國傳統修正方法的溫度統一誤差修正公式。
In the paper , through the calibration test of ground load , the relationship between outputs of electrical resistance of strain gauges and the external load applied on the structure has been gotten , and then the load history can directly be deduced from the measured strain history . so the fatigue load can be compiled 本文所建立的應變法實測疲勞載荷,其主要方法是通過進行地面加載標定實驗,確定所設計應變電橋輸出量與結構上作用的外載荷之間的關系,再由實測應變歷程直接得到載荷歷程的方法。
3 . a series of quasi - dynamic calibration tests by varying the pressure pulse width for the < t > 3 . 5 x 8 . 75mm pillar copper cylinders and o 4 . 763mm copper spheres are done on the dropper - hammer hydraulic dynamic pressure calibration device . by means of data analysis , the regulations of pulse width ' s effect on the two types of plastic pressure - measuring elements are obtained 3利用落錘液壓動標裝置組織了3 . 5 8 . 75mm柱形銅柱、 4 . 763mm銅球的變脈寬準動態校準試驗,通過試驗數據處理,獲得了兩種型號塑性測壓器件的脈寬影響規律。